Frequenty Asked Questions2022-06-20T10:49:25+00:00

ALWAYS ON HAND TO ANSWER QUESTIONS

We’re here to help

Questions about our edge banding? Want to know more about our colour match service? Check out our FAQs below. If you still can’t find what you’re looking for please, get in touch!

How Long Does Edge Banding Last?2022-06-20T10:53:20+00:00

Edge banding is a type of veneer that is applied to the exposed edges of plywood or MDF boards. It is used to give a neater appearance and to protect the edges from wear and tear. But, how long does edge banding last?

Edge banding can be made from various materials, including plastic, wood, metal, or composite.

It is usually applied with an adhesive and then trimmed flush with the surface of the board using a router or trimmer. Moreover, it’s also important to use the correct type of adhesive for the material you are using, as some adhesives may not work well with certain types of edge banding.

 

The Lifespan of an Edge Banding

The lifespan of edge banding depends on several factors, including the type of material used, the quality of the adhesive, and how well the edge banding is applied. In general, plastic and composite edge bandings will last the longest, as they are less prone to wear and tear than wood or metal.

The quality of the adhesive is also important in determining the lifespan of edge banding. A good quality adhesive will bond well to the surface of the board and the edge banding and will resist moisture and heat. A poor quality adhesive may not bond well or may allow moisture or heat to break down the bond over time.

Finally, how well the edge banding is applied can also affect its lifespan. If the edge banding is not applied evenly or if it is not trimmed flush with the surface of the board, it may peel up or chip over time.

 

Types of Edge Bandings And Their Lifespan

There are different types of edge bandings available for you to choose from. Each type has its own longevity. Here are the different types and how long each of edge banding last:

Plastic

Plastic edge bandings are made from PVC, ABS, or PET. They are available in a variety of colors and textures and can be purchased pre-glued or unglued. Plastic edge bandings are durable and resistant to moisture, heat, and UV light. They are also easy to apply and trim. Plastic edge bandings typically have a lifespan of 5-10 years.

Wood

Wood edge bandings are made from real wood veneers. They are available in a variety of colors and grain patterns and can be purchased pre-glued or unglued. Wood edge bandings require more care than plastic when applying and trimming, as they can chip or splinter if not done properly. Wood edge bandings typically have a lifespan of 2-5 years.

Metal

Metal bandings are made from aluminum, stainless steel, or brass. They are available in a variety of colors and finishes and can be purchased pre-glued or unglued. Metal edge bandings are durable and resistant to moisture, heat, and UV light. They are also easy to apply and trim. Metal bandings typically have a lifespan of 5-10 years.

Composite

Composite bandings are made from a combination of wood and plastic. They are available in a variety of colors and textures and can be purchased pre-glued or unglued. Composite edge bandings are durable and resistant to moisture, heat, and UV light. They are also easy to apply and trim. Composite edge bandings typically have a lifespan of 5-10 years.

 

Applying Edge Banding

Edge banding can be applied with an adhesive or with heat. Adhesive-applied banding is the most common type, as it is easy to apply and trim. Heat-applied banding requires special equipment and is more difficult to apply, but it creates a stronger bond between the banding and the board.

To apply adhesive-applied banding, first, clean the surface of the board with a damp cloth to remove any dust or debris. Next, apply a thin layer of adhesive to the surface of the board. Be sure to apply the adhesive evenly to avoid any gaps. Then, place the banding on the board and press it into place. Use a roller or your hands to smooth out any bubbles or wrinkles.

Finally, trim the banding flush with the surface of the board using a router or trimmer. It is important to use the correct type of adhesive for the material you are using, as some adhesives may not work well with certain types of banding.

To apply heat-applied banding, first, clean the surface of the board with a damp cloth to remove any dust or debris. Next, apply a thin layer of adhesive to

 

Tips for Prolonging the Lifespan of Edge Banding

When you want to keep your banding looking new for as long as possible, there are a few things you can do:

 

  •       Use a high-quality adhesive: A high-quality adhesive will create a stronger bond between the banding and the board, and will resist moisture and heat.
  •       Apply the edge banding evenly: If the banding is not applied evenly, it may peel up or chip over time.
  •       Trim the banding flush with the surface of the board: If the banding is not trimmed flush with the surface of the board, it may also peel up or chip over time.
  •       Use a clear coat: A clear coat of polyurethane or lacquer will protect the banding from scratches, moisture, and UV light.
  •       Store the board in a cool, dry place: extreme temperatures can cause the edge banding to warp or discolor.

 

Edge banding is a great way to finish off the edges of your project boards. It can give them a professional look and prolong the life of your boards. With proper care, your edge banding can last for many years.

 

Conclusion

Edge banding is a great way to finish off the edges of your project boards. It can give them a professional look and prolong the life of your boards. With proper care, your banding can last for many years. There are a variety of materials available, and each has its own benefits and drawbacks. Choose the material that best suits your needs and follow the tips above to keep your edge banding looking new for as long as possible.

For more banding tips and services, we at Cadre Components will be happy to help you. We have years of experience and training in edge banding and we offer it at an affordable price. Whether you need veneer edge banding or aluminium ones, we got you. Contact us today!

 

What Are The Different Types Of Edge Banding2022-05-18T12:29:26+00:00

Edge banding is one of the most substantial types of adhesives used to attach two pieces of wood. It is also one of the most versatile, as it can be used on different materials like MDF, chipboard, and even solid wood.

If you are interested in edge banding, this article will discuss the different types of edge banding.

 

Different Types of Edge Banding

Depending on the application, there are different types of banding that you can choose from.

 

Plastic Edge Banding

This type of banding is used to cover the exposed edges of materials like plywood and particleboard. The edge banding is glued or heated welded onto the edge of the material. It provides a finished look as well as protects the edges from damage.

 

There are many different types of plastic edge banding available on the market, including PVC, ABS, and melamine. Each type has its advantages and disadvantages, so choosing the right one for your project is essential.

 

PVC

PVC edge banding is the most popular type because it’s durable and easy to apply. It’s also relatively inexpensive. However, PVC can be difficult to remove if you need to make repairs later.

 

ABS

ABS edge banding is less popular than PVC, but it’s still a good option for many projects. It’s more expensive than PVC, but it’s also more flexible and easier to remove.

 

Melamine

Melamine edge banding is the most expensive plastic edge banding, but it’s also durable. It’s not as flexible as ABS, so it’s not a good choice for projects that require a lot of curves. However, it’s straightforward to apply and remove, making it a good choice for repairs.

 

Paper Edge Banding

Paper edge banding is made from thin paper glued to the edge of the material. It is not as strong as PVC, but it is more flexible and can be wrapped around curves. Paper edge banding is also easy to apply with an iron or heat gun. However, it can be difficult to trim and may require a router or sander for a clean finish.

 

Wood Edge Banding

Wood edge banding is made from natural wood veneer glued to the edge of the material. It is solid and durable but can be challenging to apply evenly. Wood edge banding is also susceptible to moisture and humidity, so it is not recommended for outdoor use.

 

Metal Edge Banding

Metal edge banding is made from aluminum, stainless steel, or other metals. It is ideal for use on materials exposed to high temperatures or heavy wear and tear. Metal edge banding is also solid and can give your project a professional look. However, it can be challenging to apply and may require special tools.

 

Fiberglass Edge Banding

This edge banding is made from fiberglass and has a very smooth, glossy surface. It’s easy to clean and maintain but can be expensive.

Fiberglass edge banding is perfect for use in areas that require a high level of sanitation, such as kitchens and bathrooms. It’s also ideal for use in high-traffic areas since it’s easy to keep clean. However, the high cost can be a deterrent for some users.

In addition, fiberglass edge banding can be challenging to work with if you’re not used to it. The material is very stiff and can be hard to cut and shape. If you’re not careful, you could have a jagged, uneven edge.

Despite the challenges, fiberglass edge banding is an excellent choice for those who need a high-quality, durable product that will last for years. This is a perfect option for your home or office if you can afford it.

 

Acrylic Edge Banding

Acrylic Edge banding is one of the most popular finishes for furniture. It has a lot of benefits for both indoor and outdoor use. One of its main advantages is that it’s versatile. You can use it on wood, metal, or plastic.

There are many benefits to using acrylic edge banding over other options. Acrylic edge banding is very versatile and can be applied to various surfaces. It is also very durable and will last long.

Moreover, acrylic edge banding is easy to apply and remove. It can be used with a brush or roller and released with a putty knife.

If you are looking for an edge banding option that is versatile, durable, and easy to use, then acrylic edge banding may be the right choice.

 

Wood Veneer Edge Banding

A wood veneer edge banding is a narrow strip of wood used to cover the exposed edges of plywood or particleboard. It is available in various thicknesses and widths and can be applied with an adhesive or by the heat-activated film.

Edge banding provides a finished look to furniture and cabinets and can also protect plywood’s edges from chipping or splitting. It is typically made from a hardwood veneer, such as maple, oak, or cherry, although softwood veneers, such as pine, are also available.

Moreover, edge banding is typically affixed to the edges of plywood or particleboard with an adhesive. However, some types are heat-activated and require an iron or other heat source. It is essential to select the type of edge banding that is best suited for the project at hand and the adhesive or heat-activated film that will work best with the surface it will be applied.

To ensure the longevity of your edge banding, it is important to use the proper adhesive. Edge banding adhesives are typically water-based, hot-melt, or pressure-sensitive. Water-based adhesives are the most common type and work well with most types of edge banding materials. Hot-melt adhesives are activated by heat and provide a very strong bond. Pressure-sensitive adhesives do not require any heat or water and can be applied directly to the surface.

 

Conclusion

There are many different types of edge banding available on the market, each with its advantages and disadvantages. The best edge banding for your project will depend on the material you’re using, the desired look, and the level of durability you need. With so many options available, there’s sure to be an edge banding perfect for your needs.

Does an Edge Banding Hold Up?2022-05-18T12:46:36+00:00

Edge banding is a process where a strip of material is applied to the edge of a piece of wood. This can be done for a number of reasons, including decorative purposes or to protect the wood from damage. But how does an edge banding hold up?

 

The main purpose of edge banding is to give the illusion of a solid piece of wood when in reality it is made up of multiple pieces that have been joined together. Edge banding can be made from a variety of materials, including plastic, metal, or even veneer.

 

How Does Edge Banding Hold Up?

Edge banding can be a great way to protect your wood furniture from damage. It can also give your furniture a more polished and finished look. However, it is important to note that edge banding is not indestructible. With proper care and maintenance, your edge banding should last for many years to come. Here are a few tips on how to make sure your edge banding hold up:

 

1. Avoid Water Damage

One of the most common ways that edge banding gets damaged is through water exposure. Water can cause the adhesive holding the banding in place to break down, resulting in the banding becoming loose or falling off entirely.

To avoid this, keep your furniture away from sources of water such as windows, sinks, and water heaters. In addition, be sure to wipe up any spills promptly. This will ensure that your edge banding hold up longer.

 

2. Avoid Extreme Temperature Changes

Just like water, extreme temperature changes can also cause damage to edge banding. When the temperature gets too cold, the adhesive can become brittle and crack.

Conversely, when the temperature gets too hot, the adhesive can become soft and gooey, making it difficult for the banding to stay in place. To protect your edge banding, avoid placing your furniture near heaters or air conditioners.

 

3. Use Coasters

One of the best ways to protect your edge banding (and your furniture) is to use coasters. Coasters help distribute weight evenly, which prevents the banding from becoming loose over time. In addition, they also protect the surface of your furniture from scratches and water damage.

 

4. Avoid Sharp Objects

Sharp objects can cause scratches, dents, or chips in your edge banding. To avoid this, be careful when handling sharp objects near your furniture. In addition, avoid placing sharp objects on top of your furniture, as this can cause damage even if the object doesn’t come into direct contact with the banding.

 

5. Clean Gently

When cleaning your furniture, be sure to use gentle cleaners and a soft cloth. Harsh chemicals and abrasive scrubbing can damage the finish of your edge banding (and your furniture).

In addition, be sure to avoid using too much water when cleaning, as this can cause the adhesive holding the banding in place to break down.

 

Edge banding can be a great way to protect your wood furniture and give it a more polished look. However, it is important to take care of your edge banding to ensure that it lasts for many years to come. By following the tips above, you can help make sure your edge banding holds up for years to come.

 

Tips in Doing Your Edge Banding

When done properly, edge banding can be very durable and long-lasting. However, if not done correctly, it can peel off or chip easily. Here are a few tips to help you get the most out of your edge banding:

 

Choose the right material

Not all materials are created equal when it comes to edge banding. For example, plastic is much more flexible than metal, so it is better suited for curved edges. Metal, on the other hand, is more durable and less likely to chip or peel.

 

Veneer is another popular choice for edge banding, although it is not as durable as plastic or metal. It can be difficult to apply evenly, so it is important to take your time and use a sharp knife to trim any excess.

 

Prepare the surface

Before applying the edge banding, it is important to clean and sand the surface of the wood. This will help the adhesive adhere better and prevent any air bubbles from forming.

 

If you are using veneer, you will also need to apply a thin layer of glue before attaching it. Be sure to use an even amount and allow it to dry completely before proceeding.

 

Apply pressure

Once the adhesive is in place, use a roller or your fingers to apply pressure to the edge banding. This will help it bond better with the wood and prevent it from peeling up later.

 

Trim any excess

Once the edge banding is in place, use a sharp knife to trim off any excess material. Be sure to go slowly and be careful not to damage the underlying wood.

 

With these tips, you should be able to get long-lasting results from your edge banding. With a little practice, you’ll be an expert in no time!

 

Methods in Applying Edge Banding

There are a few different methods that can be used to apply edge banding, including adhesive tape, hot melt glue, and veneer. Each method has its own advantages and disadvantages, so it’s important to choose the right one for your project.

 

Adhesive tape.

Adhesive tape is the most popular method of applying edge banding. It’s quick and easy to use, and it produces a very strong bond. However, it can be difficult to remove if you need to make repairs later on.

 

Hot melt glue.

Hot melt glue is another popular choice for edge banding. It’s easy to use and produces a strong bond, but it can be messy to work with.

 

Veneer.

A veneer is a thin piece of wood that can be applied to the edge of a piece of furniture. It’s more difficult to apply than adhesive tape or hot melt glue, but it produces a very professional-looking finish.

If you’re looking for a quick and easy way to apply edge banding, adhesive tape is the way to go. If you want a more durable bond, hot melt glue is a good choice. And if you’re looking for a professional-looking finish, a veneer is the best option.

 

Is edge banding durable?

Edge banding is a very durable way to finish the edge of a piece of wood. However, it is not completely indestructible. With time and use, the edge banding can become worn or chipped.

 

To extend the life of your edge banding, it is important to choose the right material for your project. For example, metal is more durable than plastic and veneer.

 

It is also important to apply the edge banding properly. Be sure to clean and sand the surface of the wood before applying the adhesive. And be sure to apply pressure to the edge banding after it has been applied, in order to ensure a strong bond.

 

With proper care and maintenance, your edge banding should last for many years.

 

Is Edge Banding Real Wood?2022-05-18T13:08:32+00:00

When you do decorative wooden projects, edge banding is an essential finishing touch. It is a process where a thin strip of wood veneer is glued onto the exposed edge of a plywood or MDF substrate. This gives the illusion that the piece is made out of solid wood when in reality it is not. This is where edge banding comes in.

 

So, what exactly is edge banding? Is edge banding real wood? The answer to both of these questions is yes and no. Let’s take a closer look at each one.

 

Is edge banding real wood?

The answer to this question is a bit more complicated. While the veneer itself is real wood, the substrate that it is glued onto is not. Plywood and MDF are both made from wood fibers, but they are not solid pieces of wood. They are composites, which means that they are made from wood chips that have been glued together.

So while the edge banding veneer is real wood, the substrate is not.

Edge banding is a real wood veneer that is glued onto the exposed edge of a plywood or MDF substrate. However, the veneer itself is very thin, usually only about 1/8 inch thick. So while the veneer is real wood, it’s not very thick.

 

What is edge banding made of?

There are several materials you can use for edge bandings, such as ABS edge banding, aluminum edge banding, acrylic edge banding, and veneer edge banding. Let’s take a deeper look into each type:

ABS Edge Banding: ABS, or acrylonitrile butadiene styrene, is a type of plastic that is often used for edge banding. It is a durable material that can be heat-formed to create different shapes.

Aluminum Edge Banding: Aluminum is another popular choice for edge banding. It is a strong metal that can give your project a more industrial look.

Acrylic Edge Banding: Acrylic edge banding is made from a type of plastic called polymethyl methacrylate (PMMA). It is a clear material that can be used to create a seamless finish.

Veneer Edge Banding: Veneer edge banding is made from thin slices of wood that are glued onto the substrate. It is available in a variety of wood species, such as oak, maple, and cherry.

 

How is edge banding applied?

Edge banding is applied using an adhesive, such as PVA glue or hot melt adhesive. The veneer is then placed onto the substrate and trimmed to size.

To install edge bandings, these steps should be followed:

1. Cut the veneer to size

The size of the veneer edge banding should be measured properly. If you don’t cut it to the right size, it will be too big or small for your project.

2. Apply the adhesive

The next step is to apply the adhesive to the substrate. You can use a brush, roller, or spray bottle to apply the adhesive. Make sure that you evenly cover the entire edge with adhesive.

3. Place the veneer onto the substrate

After the adhesive has been applied, you can now place the veneer onto the substrate. Starting at one end, align the edge of the veneer with the edge of the substrate and press it down firmly. Continue until you reach the other end.

4. Trim the excess veneer

Once you have placed all of the veneers onto the substrate, you can now trim the excess. You can use a utility knife or a veneer trimmer to do this.

5. Apply pressure to the veneer

After trimming the excess veneer, you should apply pressure to the entire length of the veneer. This will help to bond the veneer to the substrate.

6. Allow the adhesive to dry

Once you have applied pressure to the veneer, you should allow the adhesive to dry. This usually takes about 24 hours.

 

What are the benefits of edge banding?

There are several benefits to using edge banding, such as:

 

It gives the illusion of a solid wood piece: Edge banding can make a plywood or MDF piece look like it is made out of solid wood. This is because the veneer is glued onto the exposed edge, which gives the illusion that the piece is made out of solid wood.

 

It protects the edges: Edge banding can help protect the edges of a plywood or MDF piece from chipping or damage. This is because the veneer acts as a barrier between the edge of the substrate and the outside world.

 

It is available in a variety of materials: As we mentioned before, there are several materials that you can use for edge bandings, such as ABS, aluminum, acrylic, and veneer. This gives you a lot of options to choose from so that you can find the right material for your project.

 

It is available in a variety of colors: Edge banding is also available in a variety of colors. This means that you can find the perfect color to match your project.

 

What are the disadvantages of edge banding?

While there are several benefits to using edge banding, there are also some disadvantages, such as:

 

It can be difficult to apply: Applying edge banding can be a bit tricky, especially if you are doing it for the first time. If you don’t do it correctly, the veneer can peel off or the adhesive can come undone.

 

It is not always necessary: In some cases, edge banding may not be necessary. This is because the edges of the substrate may not be exposed or they may not be susceptible to damage.

 

It can be expensive: Depending on the material that you use, edge banding can be quite expensive. This is because some materials, such as veneer, can be expensive to purchase.

 

Can edge banding be sanded?

Yes, edge banding can be sanded. However, it is important to note that you should only sand the veneer and not the substrate. Sanding the substrate can damage the material.

 

What are some common problems with edge banding?

Some common problems with edge banding include:

 

Bubbling: This is when the adhesive creates bubbles under the veneer. This can happen if the adhesive is not applied correctly or if the veneer is not pressed down firmly enough.

 

Peeling: This is when the veneer starts to peel off of the substrate. This can happen if the adhesive is not strong enough or if the veneer was not trimmed properly.

 

Gaps: This is when there are gaps between the veneer and the substrate. This can happen if the veneer was not placed properly or if it was not trimmed correctly.

 

Is edge banding worth it?

The short answer is yes, edge banding is definitely worth it! It can give your project a clean and professional look while also protecting the edges of your substrate from damage. Plus, it’s not very difficult or time-consuming to apply. So if you’re looking for an easy way to spruce up your project, edge banding is a great option!

 

What Are Edge Bandings And What Does It Do?2022-05-18T13:37:51+00:00

When you are doing woodworks, edge banding is a term you will often hear. So, what are edge bandings? This reading will show you a full guide on edge banding.

 

What is edge banding?

Edge bandings is the process of attaching strips of material to the exposed edges of plywood or particle board. The strips can be made of wood, laminate, or melamine.

Moreover, edge banding protects the edges of the boards from damage and gives them a finished look. It also makes it easier to clean up the edge when you are doing woodworking projects.

 

Why do you need edge banding?

There are several reasons why you might want to use edge banding on your project, such as:

 

It is a protection for your plywood or particle board.

Edge bandings are attached to the exposed edges of the plywood or particle board to protect them from damage. It also makes it easier to clean up the edge when you are doing woodworking projects.

 

It gives a finished look to your project.

If you are using plywood or particle board for a project that will be visible, such as shelves or cabinets, edge banding can give it a finished look.

 

It can make your project stronger.

Adding an edge banding to your project can make it stronger and less likely to warp or crack.

 

How to do edge banding?

There are several ways to do edge banding, but the most common way is to use an edge bander. An edge bander is a machine that applies the edge banding material to the edge of the board. It has a roll of edge banding material, and as it moves along the edge of the board, it applies pressure to attach the edge banding.

 

Edge banders come in different sizes, depending on the width of the boards you will be working with. They also have different features, such as those that allow you to cut slots for shelves or routes for electrical wiring.

 

If you are doing a small project, you can buy an edge bander that is designed for use with a hand-held router. This type of edge bander is less expensive than a larger machine, but it takes more time to use.

 

What are the different types of edge banding?

There are several types of edge banding available, including:

 

Wood edge banding.

A wood edge banding is a great banding choice to make since it is more durable than other options and it can provide a natural look for your project. However, it is important to note that a wood edge banding will not adhere as well to particle board as it does to plywood.

 

Laminate edge banding.

A laminate edge banding is a good choice if you want a finished look for your project. Laminate edge bandings are available in many colors and patterns, so you can find one that matches the rest of your project. Laminate edge bandings are also more resistant to damage than other types of edge banding.

 

Melamine edge banding.

A melamine edge banding is an economical choice for your project. Melamine is a type of plastic, and it is available in many colors and patterns. Melamine edge bandings are less durable than laminate or wood edge bandings, but they are easier to apply.

 

PVC edge banding.

A PVC edge banding is a good choice if you want a durable edge banding that is easy to apply. PVC edge bandings are available in many colors and patterns, and they are resistant to damage. However, PVC edge bandings can be difficult to remove if you need to make repairs to your project.

 

What are the different sizes of edge banding?

Edge banding is available in different widths, depending on the thickness of the boards you will be working with. The most common widths are 1/2 inch, 3/4 inch, and 1 inch.

 

What is the best type of edge banding for your project?

The best type of edge banding for your project depends on the type of wood you are using, the size of your project, and the look you are trying to achieve. If you are unsure which type of edge banding to use, ask a salesperson at your local home improvement store for advice.

 

How to Choose The Right Edge Banding For Your Project

When you are choosing edge banding for your project, there are several things to consider, including:

 

The type of wood you are using.

If you are using plywood, particle board, or MDF, you will need to use a different type of edge banding than if you are using solid wood.

 

The size of your project.

If you are doing a large project, such as cabinets or shelving, you will need to use a larger width of edge banding. If you are doing a small project, such as a jewelry box, you can use a smaller width of edge banding.

 

The look you want to achieve.

If you want a finished look for your project, laminate or wood edge banding would be a good choice. If you want an economical choice, melamine edge banding would be a good choice.

 

What is the difference between pre-glued and non-glued edge banding?

Pre-glued edge banding has an adhesive already applied to it, so all you need to do is apply pressure to attach it to the edge of the board. Non-glued edge banding does not have an adhesive, so you will need to apply glue to both the edge banding and the board before attaching it.

 

How do you attach edge banding?

If you are using pre-glued edge banding, all you need to do is apply pressure to attach it to the edge of the board. If you are using non-glued edge banding, you will need to apply glue to both the edge banding and the board before attaching it.

 

To attach edge banding, you will need:

 

  • Edge banding.
  • Wood glue.
  • A putty knife.
  • A clamps.

 

  1. Apply wood glue to the edge of the board.
  2. Place the edge banding on the board, aligning it with the edge.
  3. Use a putty knife to press the edge banding onto the board.
  4. Place clamps on the edge banding, and let the glue dry for 24 hours.
  5. Remove the clamps.

 

Edge banding may seem like a small detail, but it can make a big difference in the finished look of your project. By taking the time to choose the right edge banding and attach it properly, you can create a professional-looking project that will be sure to impress.

 

Go to Top